Tips for using liquid silicone
Liquid silicone is a highly active adsorption material that is widely used in many fields such as electronics, medical treatment, and daily necessities. Here are some tips for use:
Preparation
Understand the characteristics: Different types of liquid silicone have different properties, such as viscosity, curing time, hardness, and tensile strength. You need to fully understand its characteristics before use. For example, when used to make food molds, you should choose liquid silicone that meets food-grade standards and has appropriate softness to ensure product safety and smooth demolding.
Cleaning and protection: Before operation, make sure the work area and tools are clean to avoid impurities from mixing into the silicone and affecting the performance of the silicone. At the same time, wear protective equipment such as gloves and masks, because some liquid silicone may irritate the skin and respiratory tract.
Preheating the mold (if any): If a mold is used, preheating the mold to an appropriate temperature in advance will help the liquid silicone flow and fill better, and it can also speed up the curing speed and improve production efficiency. For example, when making silicone products with complex shapes, preheating the mold can allow the silicone to flow more evenly into every corner of the mold.
Mixing link
Accurate ratio: Most liquid silicones are composed of two components, A and B, and they must be accurately weighed and mixed in strict accordance with the product instructions. Improper proportions can lead to incomplete curing, performance changes and other problems. For example, the ratio of components A and B of a certain brand of liquid silicone is 1:1. Use an electronic scale to accurately weigh to ensure accurate mass ratio.
Fully stir: After mixing, stir thoroughly with a stirring rod or stirring equipment to ensure that the two components are evenly mixed. Stir in the same direction to avoid mixing too many bubbles. For large amounts of liquid silicone, it is recommended to use mechanical stirring to ensure mixing uniformity.
Degassing treatment
Natural degassing: If there are bubbles in the mixed liquid silicone, let it stand for a while to allow some bubbles to float up and burst naturally. For example, for liquid silicone with low viscosity, let it stand for 5-10 minutes, the bubbles will be reduced to a certain extent.
Vacuum degassing: For applications with higher requirements, a vacuum degassing machine can be used. Put the mixed liquid silicone into a vacuum degassing machine, evacuate to a certain degree and keep it for a while to quickly discharge the bubbles. For example, liquid silicone used to make optical lenses needs to be vacuum degassed to ensure the optical performance of the product.
Infusion and molding
Control flow rate: During infusion, control the flow rate and flow of liquid silicone so that it flows slowly and evenly into the mold or is coated on the substrate. Too fast infusion is prone to produce bubbles and flow marks, affecting product quality. For example, when making silicone jewelry, use a syringe or glue dripping tool to slowly infuse to ensure that the surface of the jewelry is smooth.
Ensure filling: During the infusion process, ensure that the liquid silicone completely fills all parts of the mold. For molds with complex structures or deep holes, the mold can be vibrated appropriately to assist the silicone flow filling. For example, when making silicone stamps with fine patterns, vibrating the mold can allow the silicone to fill the pattern details.
Curing conditions: According to the product instructions, provide appropriate curing conditions, such as temperature and time. Some liquid silicone can be cured at room temperature, but heating can speed up the curing speed and improve the curing quality. For example, some silicones take 24 hours to cure at room temperature, and heating to 60-80℃ may cure in a few hours.
Demolding and post-processing
Timely demolding: After reaching the curing time, first determine whether the silicone is completely cured, and then demold. Demolding too early may cause deformation and damage to the product, while demolding too late may increase the difficulty of demolding. For example, if you press the surface of the silicone lightly with your fingers and it is not sticky and has a certain elasticity, it means that it has been initially cured and can be demolded.
Surface treatment: After demolding, if there are burrs and flaws on the surface of the product, you can use tools such as knives and sandpaper to trim them, or you can perform post-treatment such as secondary vulcanization to improve the physical properties of the product, such as improving hardness and wear resistance.
liquid silicone use tips
Jan 16, 2025 Leave a message
Send Inquiry

